advertencia en administrador de dispositivo sci

Hola
http://support.microsoft.com/?kbid2604
Creo que en estos casos, la norma es que los perifericos menos exigentes
a la hora de tomar recursos, se instalan los últimos.
Lee detenidamente, las instrucciones del dispositivo que instalas.Tendrá indi
caciones sobre estos recursos irq
En el administrador de dispositivos MI PC propiedaes, veras la asignación
de los mismos.
Es un tema para avanzados, que no conozco.

"marcelo" escribió en el mensaje
news:022c01c3ac7a$2ff3cbc0$
me aparece una señal de advertencia cuando abro
propiedades del sistema, administrador de
dispositivos,dispositivos de sistema, sci irq utilizada
por el por el bus acpi.
mi pregunta es la siguiente, a que se debe esta
advertencia y cual es el dispositivo que la utiliza (ya
que no puedo ver detalles del archivo controlador), y cual
es dicho archivo y la forma de solucionar el problema.

desde ya muchas gracias
Marcelo

Hola
Este paisano lo arregló cambiando la tarjeta que habia instalado a otra ranura
Saludos.
Copio:
From: "Richard G. Harper"
Newsgroups: microsoft.public.windowsme.general,microsoft.public.windowsme.hardware
Sent: Sunday, November 16, 2003 3:48 PM
Subject: Re: Resource conflict


The reason Windows does not show a conflict is because it's being handled by
the computer's BIOS - it's disabling one or the other devices that has a
conflict. You need to look at the add-on cards in your PCI slots to
determine which one(s) have recently been added. You may be able to resolve
the conflict by moving the newest card to another slot.

Richard G. Harper () MVP Win9x
* Please post all messages and replies in the newsgroup so that
* all may benefit. Private mail is usually not replied to.
* Help US Help YOU ... http://www.dts-l.org/goodpost.htm


"General Mailbox" wrote in message
news:QbGtb.7070$
Greetings.
Upon power up of the tower, the monitor shows the normal white screen with
Emachines. It pauses a bit longer than usual, about 15 seconds, then the
computer gives a resource conflict PCI in slot 01 Bus:01, Device:0E,
Function:00.
If this System Information / Hardware Resources / Conflicts / Sharing area
is suppose to "flag" a conflict, then there is no conflict. I even
unplugged the cables from the mother board to all the hard disks to see if
there was a short or break in the cable and powered the tower. The same
error occurred. I will confess that before this error was noticed, I
changed the disk cable for the one disk with a cable to hook up two disks.
This cable was not polarized and had it plugged in reverse. When only the
splash screen showed for about 20 secs, I powered off the tower and
reversed
the cable. Two disks did not seem to want to work together, so now the
original disk and cable are restored. It then started working, but I
don't
remember if the error started right away or if it has anything to do with
a
reversed cable. If "<F1> to resume" is pressed, the O/S loads as if
nothing
is wrong. Please advise how to resolve the conflict. It would be greatly
appreciated!
Kevin


Equipment: TriGem Computer (Emachine) X86-based PC
Processor: Intel(r) Celeron GenuineIntel 565 Mhz
BIOS version 1.04 Total Physical Memory 190.45MB
Error screen shows:
PhoenixBIOS 4.0 Release 6.0 Version 1.04
System BIOS shadowed
Video BIOS shadowed
UMB upper limit segment address: E72F
Fixed Disk 0: Samsung SV2044D
ATAPI CD-ROM: Samsung Combo SM-304B
ATAPI CD-ROM: Samsung CD-ROM SC-140
Event log messages, enter Setup to view
Warning
Error
Resource Conflict - PCI in slot 01
Bus:01, Device:0E, Function:00